Cci-thermal-technologies HMK - Hanging Mounting Kit Manuel d'utilisateur télécharger pdf

STEP 4

Hang heater from Angle Hangers 

using two 1/2 UNC x 1-1/4 bolts, lock

washers, and nuts.

Hanging Mounting Kit Installation Instructions

For Heater Exchanger Unit Heaters

(En français à l’endos.)

STEP 3

Insert Hanger Assemblies from Step

2 through mounting holes and fasten

using lock washers and 1/2 UNC nuts.

STEP 2

Screw one Connector Hanger  and

one Adaptor Hanger  onto each steel

pipe until tight (minimum of 5 turns

each).

Pipe cut length = Distance from

support structure to top of heater LESS

Connector’s length, 4-7/8” (124mm)

STEP 1

Fasten Angle Hangers  to a

surface or structure that will support the

heater’s weight using the installer

supplied fasteners. Refer to the owner’s

manual for the heater’s weight.

Installer required to supply:

a) a method of fastening the Angle Hangers  to the supporting structure. Four 3/8” diameter, grade 5 bolts are

suggested, however, any method providing the same or greater strength may be used.

b) two pieces of 1/2”, schedule 40 or heavier, steel pipe cut to suit required installation length and threaded at

both ends.

Check that your heater model number corresponds to the model number shown on the mounting kit carton.

WARNING:

If the heater is installed on a structure that is to be transported, provide additional support for

the heater during transit. The suspended weight should not exceed 600lbs (272 kg). Refer to

the owner`s manual for mounting specifications and conditions.

Connector Hanger  must be hung

on the inside of Angle Hanger  as

shown. Rotate Connector Hanger 

to align with Angle Hanger . Do not

back off more than 3/4 turns.

Part No. 5754-2



Support Structure







Support

Structure

Installer supplied

fasteners

DIM A = Distance between mounting holes.

(Refer to owner’s manual)

4-1/2”

(114mm)







DIM A



1/2” Sch. 40, or heavier

Steel Pipe

CONTENTS

Item Qty.

Description

 2 Angle Hanger

 2 Connector Hanger

 2 Adaptor Hanger

 2 Bolt, 1/2 UNC x 1-1/4

 4 Nut, 1/2 UNC

 4 Lock Washer, 1/2”

1 2

Part No. 5754-2 1
de réf. 5754-2 2

Résumé du contenu

Page 1 - Part No. 5754-2

STEP 4Hang heater from Angle Hangers  using two 1/2 UNC x 1-1/4 bolts, lock washers, and nuts.Hanging Mounting Kit Installation InstructionsFor Heate

Page 2 - de réf. 5754-2

ÉTAPE 4Suspendre l’aérotherme aux Cornières de suspension  à l’aide de deux boulons 1/2 UNC x 1-1/4, des rondelles d’arrêt et des écrous.Instructions

Plus de documents pour Chaudière à eau Cci-thermal-technologies HMK - Hanging Mounting Kit

Voir le document Cci-thermal-technologies HMK - Hanging Mounting Kit Manuel d'utilisateur

Cci-thermal-technologies HMK - Hanging Mounting Kit Manuel d'utilisateur (1 pages)

Commentaires sur ces manuels

Pas de commentaire

Cci-thermal-technologies HMK - Hanging Mounting Kit Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Chaudière à eau Cci-thermal-technologies HMK - Hanging Mounting Kit. CCI Thermal Technologies HMK - Hanging Mounting Kit Manuel d'utilisation Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Chaudière à eau Cci-thermal-technologies HMK - Hanging Mounting Kit

Commentaires sur ces manuels

Produits connexes et manuels pour Chaudière à eau Cci-thermal-technologies HMK - Hanging Mounting Kit