Cci-thermal-technologies HPH - Hot Plate Heater (Industrial Heavy-Duty) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Chaudière à eau Cci-thermal-technologies HPH - Hot Plate Heater (Industrial Heavy-Duty). CCI Thermal Technologies HPH - Hot Plate Heater (Industrial Heavy-Duty) Manuel d'utilisation Manuel d'utilisatio

CCI Thermal Technologies Inc. 2767 Brighton Road, Oakville, ON L6H 6J4 Tel. (905) 829-4422 Fax (905) 829-4430

www.ccithermal.com

MI147 REV. 4

OPERATION AND MAINTENANCE INSTRUCTIONS

HOT PLATE HEATER - PART NO. HPH1200

1.0 INSTALLATION

This equipment is intended for heavy duty use in dry

industrial environments. The HPH is ideal for heating

liquids, melting certain solids or preheating parts for

shrink fitting.

1.1 CAUTION - Do not use this equipment in

hazardous locations, near flammable or combustible

material or to heat highly volatile substances.

1.2 For heating liquids or melting solids, use a flat

bottomed beaker, pail, or pan suitable for 550°F(290°C).

If the container has a rim around the bottom, ensure it

overhangs the plate (See Fig. 1). Plate configurations

for holding specifically shaped containers may be

specially ordered from the factory.

1.3 Loosen the lid or open a vent to prevent

potentially dangerous pressure build-up.

1.4 Maintain 3" (75 mm) minimum clearance from

combustible surfaces.

1.5 Locate the equipment on a sturdy flat surface

with ready access to a 120V power supply receptacle.

Ensure that the four support legs are secure.

2.0 OPERATION

2.1 Plug the heater in to a 120V grounded 15 amp

dedicated receptacle. The cord must not cross over

the heating plate. (You may choose to turn the heater

so that the pilot light faces sideways to protect it from

damage.)

2.2 During operation the pilot light will cycle. The

light does not indicate any particular fluid temperature.

2.3 Immediately clean up any spills of liquid.

2.4 The plate may reach temperatures up to 550°F

(290°C).

2.5 Check periodically to ensure the substance has

not evaporated from the container.

2.6 The thermostat controls the plate temperature

and has a knob at the front for set point adjustment.

The setting is determined by trial and error based on

the container and contents being heated. Higher

settings will shorten heat-up time, but may result in

over temperature. A plug-in timer can be used to

eliminate excess waiting periods.

3.0 MAINTENANCE

3.1 Inspect the power cord for nicks or other

damage.

3.2 Keep the surface of the heating plate clean.

3.3 Ensure that the four support legs are secure.

3.4 Ensure that the terminal box cover is secure.

Never remove the cover while the unit is plugged in.

Fig. 1

1 2

MI147 REV. 4 1

Résumé du contenu

Page 1 - MI147 REV. 4

CCI Thermal Technologies Inc. 2767 Brighton Road, Oakville, ON L6H 6J4 Tel. (905) 829-4422 Fax (905) 829-4430www.ccithermal.comMI147 REV. 4OPERATIO

Page 2

CCI Thermal Technologies Inc. 2767 Brighton Road, Oakville, ON L6H 6J4 Tel. (905) 829-4422 Fax (905) 829-4430www.ccithermal.comMI147 REV. 4INSTRUCT

Commentaires sur ces manuels

Pas de commentaire

Cci-thermal-technologies HPH - Hot Plate Heater (Industrial Heavy-Duty) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Chaudière à eau Cci-thermal-technologies HPH - Hot Plate Heater (Industrial Heavy-Duty). CCI Thermal Technologies HPH - Hot Plate Heater (Industrial Heavy-Duty) Manuel d'utilisation Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Chaudière à eau Cci-thermal-technologies HPH - Hot Plate Heater (Industrial Heavy-Duty)